European XFEL, the X-ray free-electron laser facility in Germany, announced on November 20, 2026 that it had stably generated hard X-rays with a photon energy of 30 keV, corresponding to a wavelength of about 0.04 nm, and transported them to an experimental area roughly 1 km away. The effective delivery rate to the experimental area was 800 pulses per second, and about 60% of the generated X-rays reached the end of the beamline. The result comes from a research team at Deutsches Elektronen-Synchrotron (DESY) and European XFEL, and it broadens the possibilities for materials research using high-energy X-rays.

The findings were published online on October 23 as a peer-reviewed paper by Ye Chen, Frank Brinker, Tianyun Long and colleagues, and appeared in Volume 13, Issue 11 of the journal Optica, dated November 20 (DOI: 10.1364/optica.610411). European XFEL had been attempting 30 keV X-ray lasing and transport for some time. The new study quantitatively evaluated the delivery rate to the experimental area and the transmission efficiency.

AD

30 keV lasing was first achieved in 2021

This is not the first time European XFEL has produced 30 keV X-rays. According to a report Chen and colleagues presented at the 2024 International Particle Accelerator Conference (IPAC), 30 keV lasing was achieved at the SASE2 beamline in 2021, and transport to the experimental area was tested in 2022 and 2023. Building on those results, the new Optica paper clarifies how many pulses can actually be delivered to the experimental area and what fraction of the X-rays remains after transport over about 1 km.

Table 1 of the 2024 conference report records pulse energies of 340 µJ in October 2021, 40 µJ in November 2022 and 120 µJ in November 2023. It also distinguishes whether the X-rays were transported to the experimental area in each run. The 2022 test was intended to confirm the beamline's transport performance; because the required X-ray intensity was low, no dedicated tuning to strengthen the lasing was carried out. The report also named improving electron beam quality and aligning the undulators as challenges for reaching even shorter wavelengths.

About 60% of the generated X-rays transported 1 km

An X-ray free-electron laser works by accelerating electrons to high energy and passing them through an "undulator," a periodic array of magnets, to generate intense X-rays. The magnetic field repeatedly changes the electrons' direction of travel, causing them to emit radiation. This radiation interacts with the electrons and is amplified, producing a powerful laser beam. The wavelength of the X-rays depends on the electron beam energy, the strength of the undulator's magnetic field and the period of that field. In this work, the team set the fundamental photon energy to 30 keV and demonstrated stable lasing.

According to European XFEL, the team spent several years simulating the motion of the electron beam and repeating accelerator tests ahead of the demonstration. Chen of DESY explained that studying the electron beam's motion in detail and tuning the accelerator accordingly to improve beam quality was a key factor in achieving the lasing.

The 30 keV figure is the energy of a single photon, which converts to a wavelength of about 0.04 nm. The values of several hundred µJ given in the paper's public abstract, by contrast, represent the energy of an entire pulse made up of many photons. The 800 pulses per second figure indicates the effective rate at which X-ray pulses could actually be delivered to the experimental area.

The team guided the generated X-rays through the beamline optics and measured those reaching the end, about 1 km away, using instruments such as gas monitors. The transmission rate at the end, relative to the amount of X-rays generated, reached about 60%. This demonstrated not only that 30 keV X-rays can be lased stably, but also that they can be supplied to the experimental location at a high rate.

AD

Expected uses: dense materials and matter under high pressure

X-rays with higher photon energy penetrate matter more readily, making them well suited to probing the internal structure of dense materials. In X-ray scattering experiments, raising the photon energy also widens the range of momentum that can be exchanged with the sample, allowing the structure of matter to be analyzed under conditions different from those previously available.

The paper's public abstract cites these properties of high-energy X-rays as research advantages. Applications envisioned by European XFEL include observing instantaneous changes in matter under high pressure and studying catalysts and quantum materials. In particular, the technique is expected to be applied to experiments that examine the interior of materials under intense pressure while tracking structural changes that occur in very short times. How fine a structure can actually be resolved, however, depends on detector performance, the optics and the measurement conditions.

What the paper and the facility's announcement mainly demonstrate is the delivery performance from the X-ray source to the experimental area. Neither the public abstract nor the announcement gives details such as measurement duration, number of trials, pulse-to-pulse variation, or absolute X-ray intensities before and after transport. Replication under equivalent conditions by an independent facility has not been reported either.

European XFEL is continuing to improve detectors, optics and the diagnostic instruments that measure beam conditions in preparation for experiments using short-wavelength X-rays. Development of superconducting undulators is also ongoing. The timing and conditions for offering 30 keV X-rays for regular user experiments have not yet been announced, and the next test will be how much resolution can be obtained in measurements of actual materials and samples under high pressure.