Samsung Electronics, SK hynix and Micron have set up a working-level group to standardize how mobile robots are charged in semiconductor fabs, according to an exclusive report by Korea's Seoul Economic Daily on November 8. The three companies compete in the DRAM market, and their cooperation reflects a practical problem: when multiple types of robots are deployed in older fabs, it is hard to find room for a separate charging station for each model. A chipmaker-led push for common specifications also echoes the transition to 300mm wafers, which began in 1997. However, SEMI's public listings contain no formal proposal on charging-equipment standardization yet, and the approval target for a related AMR (autonomous mobile robot) safety guideline is set for October 2029. It will likely take years for any standard to take hold across the industry.
From battery specs to BMS: the scope of the memory trio's talks
According to Seoul Economic Daily, the group is an early-stage body launched by working-level staff from the three companies, and major industry organizations including SEMI (Semiconductor Equipment and Materials International) are reportedly participating. The areas targeted for standardization include battery specifications for mobile robots, communication and equipment specifications for charging stations, charger connection components, and BMS (battery management systems). The three companies are considering using humanoids, AMRs and mobile manipulators (robot arms on mobile bases) to automate older fabs, and the talks cover these kinds of mobile robots.
According to the paper's page-3 article, the first goal is to let robots from different manufacturers and of different models use the same charging equipment. A later stage may link charging data to MES (manufacturing execution systems) so that each robot's operating and charging time can be allocated according to production plans.
TrendForce data shows the three companies' combined revenue share in the second-quarter 2026 DRAM market reached 87.6%: Samsung at 39.4%, SK hynix at 24.9% and Micron at 23.3%. Jang Young-jae, director of the KAIST Manufacturing Physical AI Research Institute, told Seoul Economic Daily that a common charging standard would reduce the burden of deploying, validating and maintaining robots, and would also limit dependence on specific vendors.
Why charging? Transport gaps in older fabs that OHT can't reach
In newer fabs, OHT (overhead hoist transport) systems, which carry wafer containers along ceiling rails, and stockers, which temporarily store wafers between process steps, handle much of the transport. But OHT can only run along routes where rails are installed. In older fabs without sufficient rails or stockers, floor-level transport still requires people. In the paper's page-3 article, an industry source explains that "in older fabs, workers often still carry wafer containers on hand carts." Examples cited include parts of the lines at Samsung's Giheung campus and SK hynix's Cheongju campus.
Battery-powered mobile robots are being introduced to automate this floor-level transport. But beyond the robots themselves, space is needed for charging stations. If each model uses a different charging method, each needs its own equipment, and older fabs lack spare room. Park Soo-han, a professor in the Department of Robotics at Kwangwoon University, pointed out that without unified charging methods, more items need safety validation and management, and that an industry standard would shorten safety certification procedures and make robot deployment easier.
Plans to combine multiple types of robots are also advancing. According to Korea's Asia Economy, Samsung showed a video at GTC 2026 in March 2026 in which a humanoid receives parts delivered by an AMR and inspects manufacturing equipment.
Meanwhile, an industry standard already exists for mobile robot communication. Version 3.0 of VDA 5050, released on March 19, 2026 by Germany's Association of the Automotive Industry (VDA), defines communication between mobile robots and higher-level control systems. In addition to commands to start and stop charging, it supports notifications of charging status and remaining battery level. However, it does not specify the physical specifications of charging equipment.
The battery specifications, connection components and BMS covered by the new talks are hardware-side specifications that existing communication standards do not unify. Because charging-station communication methods are also on the agenda, it is not yet clear how the work will be divided with VDA 5050.
In the 1997 300mm shift, chipmakers also led common transport specs
There is precedent for chipmakers leading efforts to set common specifications for equipment and facilities. According to an article written on October 1, 1997 by then-SEMI president Stanley Myers, the I300I consortium of US, European and Asian chipmakers and Japan's J300 produced joint guidelines for 300mm wafer manufacturing equipment and materials after about a year of cooperation. Myers explained that while earlier wafer-size increases had been driven by individual manufacturers, the 300mm transition was the first to proceed through consortia. The cost to the equipment and materials industries from this transition was estimated at more than $14 billion.
The joint guidelines covered a wide range, from equipment utility connections to seismic anchoring, but the top priority in 1997–1998 was compatibility among wafer containers, load ports (the container interfaces on equipment) and transport systems. For containers, FOUPs (front opening unified pods) and open cassettes were prioritized, with compatibility required with standard load ports conforming to SEMI E15.1. AGVs (automated guided vehicles) and PGVs (person-guided vehicles) were required to support FOUPs and open cassettes, and OHT to support FOUPs. The emphasis was that containers, load ports and transport systems should work together even when products come from different manufacturers.
Myers explained that, based on past transition experience, early standardization can reduce the number of specification types that equipment and materials makers must develop and support. The talks over mobile robot charging are likely driven by a similar aim.
| Comparison | 300mm transition (1997 joint guidelines) | Mobile robot charging (November 2026 report) |
|---|---|---|
| Leading organization | Chipmaker consortia (I300I, J300) | Early-stage group of working-level staff from the three memory makers; SEMI and others reportedly participating |
| Scope of standardization | Compatibility of FOUPs, open cassettes, load ports and transport systems; also equipment connections and seismic measures | Mobile robot battery specifications, charging-station communication and equipment specifications, connection components, BMS |
| Expected benefits | Fewer specification types for equipment and materials makers to develop and support | Lower deployment, validation and maintenance burden and less vendor dependence; may also reduce the specification-compliance burden on robot makers |
What the 1997 300mm transition and the current charging talks share is that chipmakers are trying to unify specifications ahead of equipment makers. In particular, both emphasize common interfaces for connecting different products rather than the internal structure of equipment or robots. If charging-equipment specifications are unified, robot makers will need to develop fewer different charging interfaces for Samsung, SK hynix and Micron fabs.
However, the two efforts differ greatly in how far standardization has progressed. In the 300mm transition, joint guidelines were documented after about a year of discussion, and a plan to advance standardization through SEMI's standards development process was also indicated. The current charging talks, by contrast, are an early-stage initiative launched by working-level staff at the three companies, and details of participating organizations and the division of roles with the robot industry have not been officially disclosed.
No charging standard proposal at SEMI yet; activity through end-2027 will be key
The challenge for standardization is that chipmakers alone cannot determine robot charging specifications. Seoul Economic Daily also reports that how the semiconductor and robot industries will divide roles for each item in the standard has not been decided. The fact that charging methods differ among robot makers also complicates standardization.
For example, Boston Dynamics' production humanoid Atlas, announced on January 5, 2026, is described as having about four hours of battery life in normal use and being able to operate around the clock by swapping its own battery autonomously in under three minutes. Meanwhile, in the US, ASTM International's F45 committee, together with Enterprise Singapore, is developing a draft specification (work item WK95917) for universal wireless chargers for AGVs and AMRs. Different robots use different approaches, including swappable batteries, wired charging and wireless charging.
Some chipmakers are also moving into robot development themselves. Korea JoongAng Daily reported on September 1 that Samsung had created an "AX/PI" team in its semiconductor division to develop and deploy robots for fab automation. Chipmakers leading the drafting of common specifications may also end up on the robot development side.
Still, differences in charging methods do not necessarily prevent the talks themselves. In the 1997 300mm transition, too, priority went to standardizing the interface between wafer containers and load ports rather than unifying all transport methods. Here, too, if the scope is narrowed to charger connection components, communication and BMS integration, there is room for different charging methods to coexist. How far standardization can go will depend on whether robot makers join and what is agreed.
A useful reference for estimating how long standardization takes is SEMI's public list of task forces and document proposals. Standardization work on safety and communication for mobile robots used in semiconductor fabs has already begun.
| Date | Event |
|---|---|
| December 3, 2025 | SEMI Japan's EH&S (environment, health and safety) committee launches a task force on mobile maintenance robot safety |
| March 6, 2026 | SEMI Korea's EH&S committee launches a task force on fab service robot safety |
| March 19, 2026 | VDA 5050 version 3.0 released |
| June 17, 2026 | Work begins on a maintenance robot communication guide (Document 7476, Japan region); approval target is December 15, 2026 |
| July 9, 2026 | Work begins on an AMR safety guideline for semiconductor manufacturing (Document 7490, Korea region); first draft target is March 1, 2027 and approval target is October 1, 2029 |
| November 8, 2026 | Seoul Economic Daily reports on the three memory makers' charging standardization talks |
As of November 18, 2026, SEMI's public listings include three task forces and three document proposals related to mobile robots. However, no document proposal directly targeting standardization of charging methods or robot batteries can be found. The list contains task force registration notices and formal work proposals for new or revised standards. Informal groups are not covered, so the absence from the list alone cannot rule out the existence of the talks.
Even after formal work begins, drafting a standard takes time. The Korea region's AMR safety guideline (Document 7490) is projected to take 1,180 days, about three years and three months, from the July 9, 2026 start to the October 1, 2029 approval target. Its technical difficulty is rated "IV," the highest of four levels. The Japan region's maintenance robot communication guide (Document 7476), by contrast, spans 181 days, about six months, from start to approval target, with a difficulty of "II." Both are target dates set by SEMI, not actual approval dates.
For the charging talks too, considerable time will likely be needed before a formal standard is available. No related document proposal has been registered yet, and drafting periods for existing robot-related standards range from about six months to more than three years. Given that the 1997 300mm transition took about a year just to produce joint guidelines, industry standardization of charging methods is likely to proceed over years.
The key indicator going forward is whether a formal document proposal is registered in SEMI's public listings. If no proposal covering charging stations, robot batteries or charging interfaces is registered by the end of 2027, the talks may be better understood as an effort to coordinate procurement specifications among the three companies rather than to develop an industry standard. Conversely, if major AMR or humanoid makers announce participation, the picture of a chipmaker-only effort would change. Once a standard is eventually approved and robot makers bring compliant products to market, even older fabs could reduce the burden of installing a charging station for each model and find it easier to deploy mobile robots from multiple manufacturers.
