On November 10, 2026, US-based Microchip Technology announced the ATFCD52, a capacitive digitizer that reads signals from tactile sensors for robots. When a flexible sensor surface touches an object and deforms, the capacitance inside it changes. The ATFCD52 converts that change into digital data, which an external processor can then use to calculate force. The maximum readout rate of 800 Hz published by the company applies to a 10×10 sensor array. It does not represent the time between detecting contact and the robot's response.
Detecting capacitance changes, with force calculation handled by an external processor
Capacitive tactile sensors work on the following principle: when a flexible surface is pressed and deforms, the "mutual capacitance" between transmit and receive electrodes changes. The ATFCD52 reads signals from sensors arranged in two dimensions and converts them into digital data. An external processor can use this data to calculate the normal force perpendicular to the contact surface and the shear force acting along it. According to Microchip, a microcontroller (MCU), microprocessor (MPU), or FPGA can be combined with the chip depending on the application.
The ATFCD52 is responsible for acquiring and digitizing signals; decisions about how to grip an object are left to the external system. The company says it designed the chip to distinguish capacitance changes of less than one femtofarad (fF). However, this is a specification for electrical signal resolution and differs from force measurement accuracy expressed in newtons. The actual accuracy of force estimation also depends on factors such as the sensor materials and external signal processing.
The 800 Hz maximum readout rate is for a 10×10 array
The ATFCD52 has up to 52 channels and can combine up to 32 transmit lines with 20 receive lines. It uses 20 parallel analog front ends to capture receive-line signals simultaneously, but the frame rate varies with the size of the sensor array.
Based on the press release and product and development materials Microchip published in November 2026, the main specifications and conditions are as follows.
| Specification / condition | Published information | What it tells us |
|---|---|---|
| Maximum array | Up to 32 transmit × 20 receive lines, 52 channels in total | Shows the electrode line configuration. The acquisition rate for the maximum array is not given |
| 10×10 acquisition rate | Up to 800 Hz | Frame rate for a 10×10 array |
| Force calculation | An external processor uses the readout data | A separate process from the IC's signal digitization |
| Evaluation connection | USB bridge EV51X39A sold separately | Must be obtained separately when setting up an evaluation environment |
The figure of 52 channels is the sum of transmit and receive lines, while 800 Hz is the readout rate for a 10×10 array. The published specifications do not make clear whether a maximum 32×20 array can be read at the same rate.
Continuous acquisition at 800 Hz gives a frame period of 1.25 milliseconds. However, this time does not include the external processor's force calculation or the processing needed to drive motors. Evaluating a robot's overall response speed requires measuring everything from sensor readout through control processing to the actual movement.
The evaluation kit lets engineers test sensor materials and noise resistance
Microchip also offers an evaluation kit, the EV-ATFCD52, with a 10×10 sensor. It has an 80-pin FPC/FFC connection and can be used to evaluate sensor materials and laminated structures made of multiple layered materials. The USB bridge EV51X39A, needed for PC-based evaluation, is sold separately.
In the ATFCD Configurator for the maXTouch Studio development software, I²C is used for device configuration and SPI for acquiring frame data. It also offers graph display of the acquired data and a function for capturing frames without dropping any, allowing engineers to check the signal characteristics of each sensor material.
Inside a robot, servo motors and other components are sources of electrical noise. The ATFCD52 supports frequency hopping, which switches the frequency used for signal acquisition, and oversampling, which reduces the effect of noise through multiple measurements. These features can mitigate noise, but the accuracy actually obtained depends on the operating environment and the sensor configuration.
The ATFCD52 can be purchased directly from Microchip and through distributors. The published performance figures are manufacturer specifications, not results measured independently by a third party. For designers considering it for a robot, it will be important to select the sensor array and readout rate they need, then verify with data acquired from their actual materials and noise environment that force can be calculated and used for grip control.
