On November 16, 2026, US geothermal developer Mazama Energy announced field results for Carbon Chill, a technology that uses carbon dioxide to cool downhole equipment in geothermal wells. The test took place in August of that year at the Athena project in Newberry, Oregon. According to the company, it drilled through rock at about 341°C while keeping equipment near the drill bit at about 90.6°C. It also reports a drilling rate of 92 feet per hour (about 28 m).

The technology is meant to keep electronics that measure a well's direction and inclination working at the bottom of the hole, even when it is surrounded by hot rock. Mazama Energy aims to develop superhot geothermal resources above 374°C, and this demonstration is a field test of one of the drilling technologies that goal requires.

AD

Cooling the bottom of the hole to protect the electronics that guide drilling

Drilling a geothermal well involves more than cutting rock with a bit. Crews must also measure the well's direction and inclination and steer toward the target. That job falls to electronics that take measurements at the bottom of the hole during drilling. Even if the drilling equipment itself can withstand high temperatures, heat that stops the measurement instruments from working properly can make it hard to control the drilling direction.

In the 2024 technical report "Drilling for superhot geothermal energy: A technology gap analysis" by Rebecca Pearce and Tony Pink, the upper temperature limit of many measurement-while-drilling instruments at the time was given as 175°C. The report, from Clean Air Task Force and the Cascade Institute, points to the heat tolerance of electronics as a drilling-technology challenge for superhot geothermal development.

According to Mazama Energy's technical overview, in conventional methods drilling mud cooled at the surface picks up heat from the surrounding rock on its way down the well, and its temperature rises. Carbon Chill, by contrast, directly cools the area near the drill bit where the electronics sit. The design concentrates cooling on the bottom of the hole, the part that needs protection from heat, rather than on the whole well.

The company uses supercritical carbon dioxide as its drilling fluid. Supercritical refers to a state, at or above a certain temperature and pressure, in which the distinction between liquid and gas disappears. Pearce and Pink's report describes CO2-based drilling as using the temperature drop that accompanies the pressure decrease as fluid exits the bit nozzles for cooling, with the gas carrying cuttings to the surface. In this approach, the drilling fluid does two jobs: cooling and removing cuttings.

As of 2024, the report rated the technological maturity of CO2-based drilling at TRL 3 and named field testing with integrated components as a future task. Mazama Energy now reports that it ran the method in an actual geothermal well and successfully cooled downhole equipment. In the official announcement, CEO Sriram Vasantharajan said, "Temperature is what makes superhot geothermal so powerful, and it's also what makes drilling so difficult."

Rock at 341°C, downhole equipment held at 90.6°C

The temperatures presented in the demonstration were 645°F (about 341°C) for the rock and 195°F (about 90.6°C) for the downhole equipment. The geothermal resources Mazama Energy aims to develop, meanwhile, exceed 374°C. These figures refer to different things and serve different purposes. They do not mean that the roughly 341°C rock itself was cooled to about 90.6°C.

Item Temperature Timing and context
Rock during the demonstration About 341°C (645°F) Field conditions at Athena, August 2026
Downhole equipment during the demonstration About 90.6°C (195°F) Equipment temperature the company says it maintained in the same demonstration
Target geothermal resource Above 374°C Future development goal

Note: Temperatures are based on Mazama Energy's November 16 announcement. Celsius figures are converted from Fahrenheit and rounded.

The downhole equipment temperature now reported is well below the 175°C limit the 2024 technical report cited for many measurement instruments. Rather than developing electronics that can withstand the same heat as the rock, the idea is to cool the surroundings of the equipment and keep it at an operable temperature. A key feature of Carbon Chill is that it controls the operating environment through cooling instead of relying only on the heat tolerance of the equipment.

There is, however, a gap between the roughly 341°C rock drilled here and the 374°C-plus resources the company is targeting. The next question is whether the cooling performance can be maintained in even hotter rock. It also matters that the system not only lowers equipment temperature but also allows stable measurements to continue during drilling.

AD

Next challenges: comparing drilling speeds and the cost of sustained operation

Mazama Energy reported a drilling rate of 92 feet per hour (about 28 m), but it has not disclosed the measured data and test conditions needed to compare this with conventional methods. We also could not find a corresponding peer-reviewed paper or independent replication. The figure alone makes it difficult to assess how much Carbon Chill's cooling contributed to faster drilling.

The published materials also lack details such as the number of tests, the measurement period, well depth, and drilled intervals. We could not confirm where the temperature sensors were placed, the time series of the measurements, or measurement error, and information on factors that affect drilling speed, such as rock type, drill bit, and operating conditions, is also lacking. Clarifying performance differences between cooling methods would require comparisons made under matched conditions.

Going forward, it will be important to see how many hours downhole equipment can operate normally in rock above 374°C and how much drilling can be completed in that time. Recording equipment temperature trends together with drilling conditions would give a more accurate picture of the relationship between cooling performance and drilling speed. Whether cooling performance holds up during long, continuous operation in particular will inform decisions about commercialization.

Operating costs also need to be examined. The 2024 technical report by Pearce and Pink names a stable supply of carbon dioxide as one of the main challenges for this method. Even if the bottom of the hole can be cooled, large costs for equipment and supply to continuously secure the amount of CO2 needed for drilling would affect the overall economics of drilling.

In an interview with TechCrunch, CEO Vasantharajan said the company aims to complete one well in 2027 with a generating capacity equivalent to up to 15 MW. Achieving that plan will depend on cooling performance and a record of sustained operation in rock above 374°C, along with drilling costs including the CO2 supply. If the company can show concretely how much time and money it takes to complete a well, it will become clearer how far Carbon Chill can improve the economics of superhot geothermal development.